ASTM F594 PDF

or visit us at ASTM F Scope – This specification covers the chemical and mechanical requirements for stainless steel. ASTM F specification covers chemical and mechanical requirements for stainless steel nuts in diameters ranging from 1/4″ to /2″. ASTM F covers seven groups of stainless steel alloys, including twelve austenitic, two ferritic, four martensitic and one precipitation hardening. BoltPort.

Author: Mauzshura Brajinn
Country: Rwanda
Language: English (Spanish)
Genre: Career
Published (Last): 18 November 2005
Pages: 20
PDF File Size: 10.2 Mb
ePub File Size: 12.2 Mb
ISBN: 743-5-19252-814-3
Downloads: 47833
Price: Free* [*Free Regsitration Required]
Uploader: Fezshura

The finished fasteners shall meet aastm applicable mechanical properties. Condition CW – When Condition CW is specified, the ferritic alloys shall be annealed in accordance to above condition A for ferritic alloys, generally by the raw material manufacturer and then cold worked to develop the specified properties.

Free Technical Information

SH satm Machined from strain hardened stock or cold worked to develop the specific properties. Seven groups of stainless steel alloys are covered, including ten austenitic, two ferritic, four martensitic, and one precipitation hardening: E When approved by the purchaser, alloy F may be furnished.

F When approved by the purchaser, alloys or Se may be furnished. Condition CW – When Condition CW is specified, the austenitic alloys shall be c594 in accordance with Condition A, generally by the raw material manufacturer and thenc old worked to develop the specified properties.

AF – Headed and rolled from annealed stock and then reannealed AH – Solution annealed and age hardened after forming CW – Headed and rolled from annealed stock thus acquiring a degree of cold work. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

  MALVASIA FELSINA PITTRICE PDF

Chemical tests; mechanical tests; and corrosion resistance shall be performed to conform with the specified requirements.

A Minimum values except where shown as maximum or as a range. CW – Headed and rolled from annealed stock thus acquiring a degree of cold work.

The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. Link to Active Ff594 link will always route to the current Active version of the standard. Condition AF – When Condition AF is specified, the ferritic alloys shall be annealed in accordance to same above condition A Ferritic Alloys after all cold working including heading and threading has been completed.

B qstm of conditions: Referenced Documents purchase separately The documents listed astn are referenced within the subject standard but are not provided as part of the standard. Condition AF – When Condition AF is specified, the austenitic alloys shall be annealed in accordance 5f94 Condition A after all cold working including heading and threading has been completed. A Unless otherwise specified on the inquiry and order, the choice of an alloy from within a group shall be at the discretion of the fastener manufacturer B See section 4.

ASTM F Specification – Boltport Fasteners LLP

A – Machined from annealed or solution annealed stock thus retaining the properties of the original material; or hot formed and solution annealed. It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application.

  HEIDNISCHES CHRISTENTUM PDF

Historical Version s – axtm previous versions of standard. ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date.

C The yield and tensile strength values for full size products shall be computed by dividing the yield and maximum tensile load value by the stress area for the product size and thread sizes determined in accordance with Test Methods F This specification covers the requirements for stainless steel nuts in specified size, inclusive, in nominal diameter in a number of alloys in common use and intended for service applications requiring general corrosion resistance.

Unless otherwise specified, all bolts, hex cap screws, and studs used with these nuts shall conform to the requirements of Specification F and shall be of the same alloy group. ASTM F covers seven groups of stainless steel alloys, including twelve austenitic, two ferritic, four martensitic and one precipitation hardening.

This abstract is a brief summary of the referenced standard. A Tensile stress areas are computed using the following formula: AF – Headed and rolled ashm annealed stock and then reannealed AH – Solution annealed and age hardened after forming.

D Yield strength is the stress at which an offset of 0.